Reply
ScarletJamie
Posts: 1,534
Registered: ‎04-22-2012

Re: WAP 610N firmware upgrade problem


commanderfirst wrote:

didnt work !


I think you need to call Cisco for that for replacement. Just let them know all troubleshooting steps were exhausted.

 

ScarletJamie
Posts: 1,534
Registered: ‎04-22-2012

Re: WAP 610N firmware upgrade problem

I think you need to call Cisco for that for replacement. Just let them know all troubleshooting steps were exhausted.

commanderfirst
Posts: 19
Registered: ‎06-29-2012

Re: WAP 610N firmware upgrade problem

no warranty my friend ,warranty expired on this device !

 

is there anyway to unbrick an access point the same way its done for WRT54g routers by using JTAG ?

commanderfirst
Posts: 19
Registered: ‎06-29-2012

Re: WAP 610N firmware upgrade problem

Hello again

I Connected the ap directly to the pc and i entered ip :169.254.125.10 and subnet 255.255.0.0 and default gateway 169.254.255.255 and now my network is identified properly but if i ping thr default gateway it shows request time out and even if i enter the gateway ip in web browser it goes to page cannot be displayed

Any idea ?
Carrot
Posts: 3,271
Registered: ‎09-07-2006

Re: WAP 610N firmware upgrade problem

With reference to your concern you can try to disable the firewall and all the other security centers installed in the computer. Once after disabling then try to ping the IP address and the default gateway and check status...

Expert
zee29
Posts: 1,168
Registered: ‎04-22-2012

Re: WAP 610N firmware upgrade problem

Hi, I would like to know what's the router that you are using? There is another way of checking if the WAP is still detected or not. If your router has a DHCP client's table it would also be good to check if the WAP is detected and shows up on the list. You can also do arp -a again while the WAP is connected to your router (this way you can check if it is able to grab an ip address from the router).

 

Please check this link for additional steps:

http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=88cee19805e143e4bdee6511b3f339a7_Checking_the_IP_a...

 

commanderfirst
Posts: 19
Registered: ‎06-29-2012

Re: WAP 610N firmware upgrade problem

Everything is disabled

If i connect the ap directly to the pc through wire and static ip and gateway 169.254.255.255 so i can see connection is enabled but no way to have the interface open through a web browser by openin IE and entering 169.254.255.255

If i dont assign static ip so it says unidentified network
commanderfirst
Posts: 19
Registered: ‎06-29-2012

Re: WAP 610N firmware upgrade problem

@zee , i tried that yesterday , i plugged the ap 610n to my linksys wrt54gs directly and did arp -a but none of the devices that populated on the list has the mac address shown on the bottom of the device.

What does it mean when the mac address shown for a device on the arp -a result are FF:FF:FF:FF etc??
Expert
zee29
Posts: 1,168
Registered: ‎04-22-2012

Re: WAP 610N firmware upgrade problem

Did you check the DHCP client's table of the router? After all the reset that you made on the device it still does not show up? Then most probably the device is no longer talking. No longer functioning.

 

BTW the mac address FF:FF:FF:FF (http://wiki.wireshark.org/Gratuitous_ARP) A gratuitous ARP request is an AddressResolutionProtocol request packet where the source and destination IP are both set to the IP of the machine issuing the packet and the destination MAC is the broadcast address ff:ff:ff:ff:ff:ff. Ordinarily, no reply packet will occur. A gratuitous ARP reply is a reply to which no request has been made.

commanderfirst
Posts: 19
Registered: ‎06-29-2012

Re: WAP 610N firmware upgrade problem

The AP doesnt show up in the DHCP table
I guess the device doesnt work anymore because its either has no firmware or corrupted one !