Showing results for 
Search instead for 
Do you mean 
Reply
Joe1099
Posts: 7
Registered: ‎08-09-2009

WRT160N v3 uPnP

I need to know how to enable uPnP on my WRT160N v3 so I can set my NAT to 1 so I can send files over xfire, can anyone please help?

Corleone
Posts: 2,785
Registered: ‎09-07-2006

Re: WRT160N v3 uPnP

So you want to open NAT  on your Router for your PS3 or for your XBOX .Below are the settings how to open the NAT on your Router for PS3.

 

Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...

On the set-up tab change the MTU Size to 1452 and click Save Settings...

Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...

Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...

1) On the first line in Application box type in ABC, in the start box type in 80 and End box type in 80, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...

2) On the second line in Application box type in DEF, in the start box type in 443 and End box type in 443, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...

3) On the third line in Application box type in GHI, in the start box type in 5223 and End box type in 5223, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...

4) On the fourth line in Application box type in JKL, in the start box type in 3478 and End box type in 3479, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...

5) On the fifth line in Application box type in MNO, in the start box type in 3658 and End box type in 3658, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...

6) On the sixth line in Application box type in PQR, in the start box type in 10070 and End box type in 10080, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings

7) Now assign the given ip address on your PlayStation ip address :- 192.168.1.20, subnet mask :- 255.255.255.0, default gateway :- 192.168.1.1...

8) Also assign the dns addresses on the PlayStation Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1

9) Turn off your modem, router, and PlayStation...Wait for a minute...

10) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the PlayStation and test it...

 

If you want to open NAT on your Router for your XBOX then you need to setup this settings on your Router.. 

 

Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...

Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...

1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...

2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...

3) Click on set-up and change the MTU Size to 1452 and click Save Settings...Click on the Status tab and take note of DNS1 and DNS2 Addresses...

4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...

5) Also assign the DNS Addresses on the Xbox Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...

6) Turn off your modem, router, and Xbox...Wait for a minute...

7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...

Joe1099
Posts: 7
Registered: ‎08-09-2009

Re: WRT160N v3 uPnP

[ Edited ]

I'm having problems getting to 192.168.1.1

 

I put it in the address bar and it takes me to a google search page, also I am not trying to set up a xbox, I need to set the NAT to 1 so I can send files to friends over instant messangers and play certain games in mutiplayer on my computer

 

I am also using windows vista home premium

I've tried connecting to 192.168.1 and I get a username and password screen, I leave username empty and type admin in lower case but nothing happens and it just reappears
Message Edited by Joe1099 on 08-10-2009 10:57 PM
Corleone
Posts: 2,785
Registered: ‎09-07-2006

Re: WRT160N v3 uPnP

Password "admin" is not working that means the Router password has been changed at the time of Router's installation for the first time...Now to get into the Router's GUI you need to reset the router

 

Press and hold the reset button for 60 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

 

If your Internet Service Providor is Cable follow this link

 

After reconfiguring your Router...you can do the settings for X-Box

 

Joe1099
Posts: 7
Registered: ‎08-09-2009

Re: WRT160N v3 uPnP

i managed to connect to the IP address and now im on

 

 

4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...

5) Also assign the DNS Addresses on the Xbox Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...

6) Turn off your modem, router, and Xbox...Wait for a minute...

7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...

 

do i skip these since im just trying to get my NAT to 1 so i can play over the computer?